Cleaning and maintenance knowledge of solid wood composite flooring Purchase knowledge of solid wood composite flooring 1. Floor surface selection: Place the floor in a bright place to see if there are any defects such as cracks, dead knots, pinhole...
Cleaning and maintenance knowledge of solid wood composite flooring
Purchase knowledge of solid wood composite flooring
1. Floor surface selection:
Place the floor in a bright place to see if there are any defects such as cracks, dead knots, pinholes, knot holes, mold, etc., but you should not be too demanding for small slip knots, color difference, etc., because this is the natural property of wood.
2. Selection of floor processing accuracy:
The quality of floor processing directly affects the laying quality. Usually, take more than 5 floors in the same packaging box and place them on the glass countertop or flat ground. Use your hands to pat the tongue and grooves tightly to cooperate, and then touch with your hands to feel whether it is flat. Then use your eyes to see if the tongue and grooves are combined. It cannot be too tight, because if it is too tight, the humidity will increase slightly during installation, and it will be difficult to match when the tongue and grooves are combined.
3. Selection of paint quality on the board:
Hold the paint board in your hand and place it obliquely in a bright place. From the end of the board, see whether the paint film is full and even, and whether there are wave-shaped indentations, etc.
4. Formaldehyde emission:
This indicator is a relatively important indicator and can usually be determined through experiments. Therefore, you can ask the operator for test data. You can also use a simple and rough method to open one of the packaging boxes, take out the floor, and smell the smell. If you smell a strong and pungent formaldehyde smell, the formaldehyde concentration in the air has exceeded the standard.
5. Moisture content:
Moisture content is the main condition for floor deformation. Therefore, the selection must be close to the local moisture content, and this value is best measured with a measuring instrument. If it cannot be measured, you can also touch it with your hands. If the hand feels cool, unpleasant and a little sticky, the moisture content will be relatively high at this time.
Note: In addition to the above technical indicators, when purchasing solid wood composite floors, you also need to refer to indicators such as glue performance, elastic modulus and static curve strength (the merchant can be required to provide relevant inspection certificates to view).
Cleaning of solid wood composite flooring
When cleaning, you can first sweep the dust and debris with a clean broom, and then wipe it manually with a wrung rag. If the area is too large, you can clean the cloth mop and then hang it up and drip the water to mop the floor. Do not wash with water, nor do you clean it with a damp rag or mop. If there is watery substance on the ground, it should be immediately wiped with a dry rag. If conditions permit, you can also apply a layer of floor wax at a certain interval to strengthen the protection of the floor. If the paint surface is damaged, you can repair it with ordinary varnish yourself or ask the manufacturer to repair it. Maintenance of solid wood composite flooring
1. Keep the floor dry and clean. It is not allowed to mop the floor with dripping mop, or wipe the floor with alkaline water or soapy water to avoid destroying the gloss of the paint surface; if the air at home is dry, the mop can be wet or put a basin of water on the heating or use a humidifier to increase humidity.
2. Try to avoid sun exposure to the sun to prevent the surface paint from aging and cracking in advance under ultraviolet rays for a long time;
3. The stains on the partial panel should be removed in time. If there is oil, you can use a rag to dip warm water and dip it in a small amount of washing powder to wipe it. If it is medicine or pigment, it must be removed before the stain is penetrated like a wooden surface;
4. Try to avoid contact with water for a long time on the floor, especially not in contact with hot water. Therefore, once hot water is sprinkled on the floor, it should be wiped dry in time;
5. It is best to wax it once every three months, and clean the stains on the surface of the floor before waxing. In fact, it is okay not to punch it, but frequent wax can maintain the finish of the floor and extend the service life of the floor.
6. Avoid sharp objects scratching the ground, do not throw cigarette butts on the floor or place things that are too hot directly, and try to avoid dragging heavy furniture.
